2016 October Cisco Official New Released 300-101 Dumps in Lead2pass.com!
100% Free Download! 100% Pass Guaranteed!
Pass 300-101 exam with the latest Lead2pass 300-101 dumps: Lead2pass 300-101 exam questions and answers in PDF are prepared by our experts. Moreover, they are based on the recommended syllabus that covering all the 300-101 exam objectives.
Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/300-101.html
QUESTION 11
Refer to the following command:
router(config)# ip http secure-port 4433
Which statement is true?
A. The router will listen on port 4433 for HTTPS traffic.
B. The router will listen on port 4433 for HTTP traffic.
C. The router will never accept any HTTP and HTTPS traffic.
D. The router will listen to HTTP and HTTP traffic on port 4433.
Answer: A
Explanation:
To set the secure HTTP (HTTPS) server port number for listening, use the ip http secure-port command in global configuration mode. To return the HTTPS server port number to the default, use the no form of this command.
Ip http secure-port port-number
no ip http secure-port
Syntax Description
port-number
Integer in the range of 0 to 65535 is accepted, but the port number must be higher than 1024 unless the default is used. The default is 443.
http://www.cisco.com/en/US/docs/ios-xml/ios/https/command/nm-https-cr-cl-sh.html#wp3612805529
QUESTION 12
A network engineer is configuring SNMP on network devices to utilize one-way SNMP notifications. However, the engineer is not concerned with authentication or encryption.
Which command satisfies the requirements of this scenario?
A. router(config)#snmp-server host 172.16.201.28 traps version 2c CISCORO
B. router(config)#snmp-server host 172.16.201.28 informs version 2c CISCORO
C. router(config)#snmp-server host 172.16.201.28 traps version 3 auth CISCORO
D. router(config)#snmp-server host 172.16.201.28 informs version 3 auth CISCORO
Answer: A
Explanation:
Most network admins and engineers are familiar with SNMPv2c which has become the dominant SNMP version of the past decade. It’s simple to configure on both the router/switch-side and just as easy on the network monitoring server. The problem of course is that the SNMP statistical payload is not encrypted and authentication is passed in cleartext. Most companies have decided that the information being transmitted isn’t valuable enough to be worth the extra effort in upgrading to SNMPv3, but I would suggest otherwise.
Like IPv4 to Ipv6, there are some major changes under the hood. SNMP version 2 uses community strings (think cleartext passwords, no encryption) to authenticate polling and trap delivery. SNMP version 3 moves away from the community string approach in favor of user-based authentication and view-based access control. The users are not actual local user accounts, rather they are simply a means to determine who can authenticate to the device. The view is used to define what the user account may access on the IOS device. Finally, each user is added to a group, which determines the access policy for its users. Users, groups, views.
http://www.ccnpguide.com/snmp-version-3/
QUESTION 13
When using SNMPv3 with NoAuthNoPriv, which string is matched for authentication?
A. username
B. password
C. community-string
D. encryption-key
Answer: A
Explanation:
The following security models exist: SNMPv1, SNMPv2, SNMPv3. The following security levels exits: "noAuthNoPriv" (no authentiation and no encryption ?noauth keyword in CLI), "AuthNoPriv109thernet109ationre authenticated but not encrypted ?auth keyword in CLI), "AuthPriv" (messages are authenticated and encrypted ?priv keyword in CLI). SNMPv1 and SNMPv2 models only support the "noAuthNoPriv" model since they use plain community string to match the incoming packets. The SNMPv3 implementations could be configured to use either of the models on per-group basis (in case if "noAuthNoPriv" is configured, username serves as a replacement for community string).
http://blog.ine.com/2008/07/19/snmpv3-tutorial/
QUESTION 14
After a recent DoS attack on a network, senior management asks you to implement better logging functionality on all IOS-based devices.
Which two actions can you take to provide enhanced logging results? (Choose two.)
A. Use the msec option to enable service time stamps.
B. Increase the logging history.
C. Set the logging severity level to 1.
D. Specify a logging rate limit.
E. Disable event logging on all noncritical items.
Answer: AB
Explanation:
The optional msec keyword specifies the date/time format should include milliseconds. This can aid in pinpointing the exact time of events, or to correlate the order that the events happened. To limit syslog messages sent to the router’s history table and to an SNMP network management station based on severity, use the logging history command in global configuration mode. By default, Cisco devices Log error messages of severity levels 0 through 4 (emergency, alert, critical, error, and warning levels); in other words, "saving level warnings or higher." By increasing the severity level, more granular monitoring can occur, and SNMP messages will be sent by the less sever (5-7) messages.
QUESTION 15
A network engineer finds that a core router has crashed without warning. In this situation, which feature can the engineer use to create a crash collection?
A. secure copy protocol
B. core dumps
C. warm reloads
D. SNMP
E. NetFlow
Answer: B
Explanation:
When a router crashes, it is sometimes useful to obtain a full copy of the memory image (called a core dump) to identify the cause of the crash. Core dumps are generally very useful to your technical support representative.
Four basic ways exist for setting up the router to generate a core dump:
Using Trivial File Transfer Protocol (TFTP)
Using File Transfer Protocol (FTP)
Using remote copy protocol (rcp)
Using a Flash disk
http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr19aa.html
QUESTION 16
A network engineer is trying to implement broadcast-based NTP in a network and executes the ntp broadcast client command. Assuming that an NTP server is already set up, what is the result of the command?
A. It enables receiving NTP broadcasts on the interface where the command was executed.
B. It enables receiving NTP broadcasts on all interfaces globally.
C. It enables a device to be an NTP peer to another device.
D. It enables a device to receive NTP broadcast and unicast packets.
Answer: A
Explanation:
The NTP service can be activated by entering any ntp command. When you use the ntp broadcast client command, the NTP service is activated (if it has not already been activated) and the device is configured to receive NTP broadcast packets on a specified interface simultaneously.
Command
Description
ntp broadcast client
Allows the system to receive NTP broadcast packets on an interface.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bsm/command/bsm-xe-3se-3850-cr-book/bsm-xe-3se-3850-cr-book_chapter_00.html
QUESTION 17
Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three.)
A. header compression
B. explicit congestion notification
C. keepalive
D. time stamps
E. TCP path discovery
F. MTU window
Answer: BCD
Explanation:
TCP Selective Acknowledgment
The TCP Selective Acknowledgment feature improves performance if multiple packets are lost from one TCP window of data.
Prior to this feature, because of limited information available from cumulative acknowledgments, a TCP sender could learn about only one lost packet per-round-trip time. An aggressive sender could choose to resend packets early, but such re-sent segments might have already been successfully received.
The TCP selective acknowledgment mechanism helps improve performance. The receiving TCP host returns selective acknowledgment packets to the sender, informing the sender of data that has been received. In other words, the receiver can acknowledge packets received out of order. The sender can then resend only missing data segments (instead of everything since the first missing packet).
Prior to selective acknowledgment, if TCP lost packets 4 and 7 out of an 8-packet window, TCP would receive acknowledgment of only packets 1, 2, and 3. Packets 4 through 8 would need to be re-sent. With selective acknowledgment, TCP receives acknowledgment of packets 1, 2, 3, 5, 6, and 8. Only packets 4 and 7 must be re-sent.
TCP selective acknowledgment is used only when multiple packets are dropped within one TCP window. There is no performance impact when the feature is enabled but not used. Use the ip tcp selective-ack command in global configuration mode to enable TCP selective acknowledgment. Refer to RFC 2018 for more details about TCP selective acknowledgment.
TCP Time Stamp
The TCP time-stamp option provides improved TCP round-trip time measurements. Because the time stamps are always sent and echoed in both directions and the time-stamp value in the header is always changing, TCP header compression will not compress the outgoing packet. To allow TCP header compression over a serial link, the TCP time-stamp option is disabled. Use the ip tcp timestamp command to enable the TCP time-stamp option.
TCP Explicit Congestion Notification
The TCP Explicit Congestion Notification (ECN) feature allows an intermediate router to notify end hosts of impending network congestion. It also provides enhanced support for TCP sessions associated with applications, such as Telnet, web browsing, and transfer of audio and video data that are sensitive to delay or packet loss. The benefit of this feature is the reduction of delay and packet loss in data transmissions. Use the ip tcp ecn command in global configuration mode to enable TCP ECN.
TCP Keepalive Timer
The TCP Keepalive Timer feature provides a mechanism to identify dead connections. When a TCP connection on a routing device is idle for too long, the device sends a TCP keepalive packet to the peer with only the Acknowledgment (ACK) flag turned on. If a response packet (a TCP ACK packet) is not received after the device sends a specific number of probes, the connection is considered dead and the device initiating the probes frees resources used by the TCP connection.
QUESTION 18
A network administrator uses IP SLA to measure UDP performance and notices that packets on one router have a higher one-way delay compared to the opposite direction.
Which UDP characteristic does this scenario describe?
A. latency
B. starvation
C. connectionless communication
D. nonsequencing unordered packets
E. jitter
Answer: A
Explanation:
Cisco IOS IP SLAs provides a proactive notification feature with an SNMP trap. Each measurement operation can monitor against a pre-set performance threshold. Cisco IOS IP SLAs generates an SNMP trap to alert management applications if this threshold is crossed. Several SNMP traps are available: round trip time, average jitter, one-way latency, jitter, packet loss, MOS, and connectivity tests.
Here is a partial sample output from the IP SLA statistics that can be seen:
router#show ip sla statistics 1
Round Trip Time (RTT) for Index 55
Latest RTT: 1 ms
Latest operation start time: *23:43:31.845 UTC Thu Feb 3 2005 Latest operation return code: OK
RTT Values:
Number Of RTT: 10 RTT Min/Avg/Max: 1/1/1 milliseconds Latency one-way time:
Number of Latency one-way Samples: 0
Source to Destination Latency one way Min/Avg/Max: 0/0/0 milliseconds Destination to Source Latency one way Min/Avg/Max: 0/0/0 milliseconds
http://www.cisco.com/en/US/technologies/tk648/tk362/tk920/technologies_white_paper09186a00802d5efe.html
QUESTION 19
Under which condition does UDP dominance occur?
A. when TCP traffic is in the same class as UDP
B. when UDP flows are assigned a lower priority queue
C. when WRED is enabled
D. when ACLs are in place to block TCP traffic
Answer: A
Explanation:
Mixing TCP with UDP
It is a general best practice to not mix TCP-based traffic with UDP-based traffic (especially Streaming-Video) within a single service-provider class because of the behaviors of these protocols during periods of congestion. Specifically, TCP transmitters throttle back flows when drops are detected. Although some UDP applications have application-level windowing, flow control, and retransmission capabilities, most UDP transmitters are completely oblivious to drops and, thus, never lower transmission rates because of dropping. When TCP flows are combined with UDP flows within a single service-provider class and the class experiences congestion, TCP flows continually lower their transmission rates, potentially giving up their bandwidth to UDP flows that are oblivious to drops. This effect is called TCP starvation/UDP dominance.
TCP starvation/UDP dominance likely occurs if (TCP-based) Mission-Critical Data is assigned to the same service-provider class as (UDP-based) Streaming-Video and the class experiences sustained congestion. Even if WRED is enabled on the service-provider class, the same behavior would be observed because WRED (for the most part) manages congestion only on TCP-based flows.
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/WAN_and_MAN/QoS_SRND/QoS-SRND-Book/VPNQoS.html
QUESTION 20
PPPoE is composed of which two phases?
A. Active Authentication Phase and PPP Session Phase
B. Passive Discovery Phase and PPP Session Phase
C. Active Authorization Phase and PPP Session Phase
D. Active Discovery Phase and PPP Session Phase
Answer: D
Comparing with others’, you will find our 300-101 exam questions are more helpful and precise since all the 300-101 exam content is regularly updated and has been checked for accuracy by our team of Cisco expert professionals.
300-101 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDeXZ6R3kxS05wV0E
2016 Cisco 300-101 exam dumps (All 183 Q&As) from Lead2pass:
http://www.lead2pass.com/300-101.html [100% Exam Pass Guaranteed]